JVCC DC-UHB40FA-C Ultra High Bond Double-Sided Tape: 1/4 in x 36 yds. (Clear)

JVCC DC-UHB40FA-C Ultra High Bond Double-Sided Tape is constructed of a clear foamed acrylic system which has excellent all-around bonding properties which allows for very high performance in the most demanding of applications. Used in the manufacture of laminated safety glass and hurricane impact glass. Bonding, sealing and fixing of shower screens, cubicle glass and plastic, glass display cabinets, refrigerated cabinets for supermarkets, and chilled drink cabinets. The pressure-sensitive acrylic composition has very good tack; has excellent adhesion to a variety of surfaces; and has high shear strength performance. The tape is carried on a red, release coated polyethylene liner that is easily removed. It has good UV resistance. Also suitable for use with attaching plastic snow guards to metal roofs.

This double-sided (AKA double-coated) will bond to most surfaces including many plastics, composites, sealed woods, and metals; however thorough evaluation is recommended when bonding to low energy surface material such as Polyethylene, Polypropylene, silicones, and Teflon. For lower energy surfaces may need to use an adhesive promoter/primer such as IPA (isopropanol) on the substrate prior to application. When applying the tape after removing the release liner be careful not to contaminate the acrylic adhesive and try to immediately bond the tape to the surface without entrapping air between the tape and the surface it is being applied to. At a minimum application-pressure should be 15 pounds per inch of tape width in order to achieve maximum bond strength. The dwell time the tape needs to be in contact with both surfaces before it reaches its maximum adhesion is 1 to 24 hours.

NOTES: Sizes shipped will typically be the tape industry standard metric-cut sizes, i.e. 24mm for each 1 inch of nominal tape width ordered (rolls are approximately 5% narrower than the nominal size). This product’s actual size is 6.3mm wide. As with any adhesive tape product it is always the user’s responsibility to determine that the product is suitable for their intended use; e.g. if you want to remove a product cleanly from a specific type of substrate please test on an inconspicuous area first. Warning: This product can expose you to chemicals including Carbon black (airborne, unbound particles of respirable size), which is [are] known to the State of California to cause cancer. For more information go to www.P65Warnings.ca.gov/.

Technical Information
– Core: 3 inch diameter plastic
– Backing/Carrier: foamed acrylic
– Adhesive: ultra-high bond acrylic
– Release Liner: red polyethylene film
– Thickness: 39.4 mils (carrier, adhesive)
– Adhesion: 96 ounces per inch (to stainless steel test panel)
– Tensile Strength: 100 pounds per inch (longitudinal)
– Service/Operating Temperature: -40F to 194F
– Dynamic Shear Strength: 70 pounds per square inch
– Short Term Temperature Resistance: up to 302°F

• JVCC DC-UHB40FA-C Ultra High Bond Double-Sided Tape is constructed of a clear foamed acrylic system that has excellent all-around bonding properties which allows for very high performance in the most demanding of applications. Used in the manufacture of laminated safety glass and hurricane impact glass. Bonding, sealing and fixing of shower screens, cubicle glass and plastic, glass display cabinets, refrigerated cabinets for supermarkets and chilled drink cabinets.
• The pressure-sensitive acrylic composition has very good tack; has excellent adhesion to a variety of surfaces; and has high shear strength performance. The tape is carried on a red, release coated polyethylene liner that is easily removed. It has good UV resistance. Also suitable for use with attaching plastic snow guards to metal roofs. The dwell time the tape needs to be in contact with both surfaces before it reaches its maximum adhesion is 1 to 24 hours.
• This double-sided (AKA double-coated) tape will bond to most surfaces including many plastics, composites, sealed woods, and metals. A thorough evaluation is recommended when bonding to low energy surface material such as Polyethylene, Polypropylene, silicones, and Teflon. For lower energy surfaces may need to use an adhesive promoter such as IPA (isopropanol) on the substrate prior to application.
• Carrier/Backing: foamed acrylic. Adhesive: ultra-high bond acrylic. Release Liner: red polyethylene film. Thickness: 39.4 mils (carrier, adhesive).
• Adhesion: 96 ounces per inch (to stainless steel test panel). Tensile Strength: 100 pounds per inch (longitudinal). Service/Operating Temperature: -40F to 194F. Dynamic Shear Strength: 70 pounds per square inch. Short Term Temperature Resistance: up to 302F. Core: 3-inch diameter plastic.